A Design and Development of Special Purpose Machine (SPM) For Drilling and Tapping Operation

Authors

  • Kiran Mahanavar  SRTTC VIT Kamshet, Pune University, Maharastra, India
  • Sandesh Mahanawar  SRTTC VIT Kamshet, Pune University, Maharastra, India
  • Vidhin Vijay  SRTTC VIT Kamshet, Pune University, Maharastra, India
  • Prof. Mukesh Mane  SRTTC VIT Kamshet, Pune University, Maharastra, India

Keywords:

VMC, SPM, Drilling and Tapping Operation

Abstract

This paper discuss the case study and comparison of productivity of component using vertical machining centre(VMC) and special purpose machine(SPM) for drilling and tapping operation. In this case study, the SPM used for drilling operation (Ø9), linear tapping operation of (Ø10) of john Deere Tractor cylinder block. In this paper the following studies are carried out 1. Time saved by component handling (loading and unloading), using hydraulic clamping, 2. Increase in productivity both qualitative and quantitative, 3. Less human intervention, indirectly reduction in operator fatigue, 4. Cost saving, and 5. Increase the profit of company.

References

  1. A. M. Takale, V. R. Naik,' Design & Manufacturing Of Multi Spindle Drilling Head?? (Msdh) For Its Cycle Time Optimisation, International Journal Of Mechanical Engineering Applications Research -Ijmear Vol 03, Issue 01; January -April 2012.
  2. Hardik J. Patel*, Bhaveshkumar P. Patel**, Prof. S. M. Patel***" A Review On Thread Tapping Operation And Parametric Study" / International Journal Of Engineering Research And Applications (Ijera) Issn: 2248-9622 www.Ijera.Comvol. 2, Issue 3, May-Jun 2012, Pp.109-\113
  3. Manish Kale, Prof. D. A. Mahajan ,Prof. (Dr.) S. Y. Gajjal", Design, Fabrication And Analysis Of Special Purpose Machine For Drilling And? Riveting Operation" ,Volume Ii, Issue Vi, June 2015
  4. E. D. Doyle And S. K. Dean, Effect Of Axial Forces On Dimensional Accuracy During Tapping, International Journal Of Machine Tool Design And Research, Pergamon Press, Vol. 14,1974, 325-333.
  5. Prof. P.R. Sawant, Mr. R. A.Barawade, "Design And Development Of? Spm-A Case Study In Multi-Drilling And Tapping Machine" International Journal Of Advanced Engineering Research And Studies.?
  6. Geethanjali R1, Nirajan Hiremath2, Shashi Kumar A3," Design Of Special Purpose Machine For Drilling And Reaming" E-Issn: 2395 -005 Volume: 03 Issue: 06| June-2016 Www.Irjet.Net? P-Issn: 2395-0072 7. Pravin Kokate,Harshal Patil Lalit Ugale Mayur Kadam Ketan Patel „Study Of Multi-Taskingmachine "isbn-878-81-32074-7-5www.Conferanceworld,In 23 March 2016

International Journal of Scientific Research in Science and Technology

Downloads

Published

2017-06-30

Issue

Volume 3, Issue 4, May-June-2017

Section

Research Articles

License

Copyright (c) IJSRST

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Kiran Mahanavar, Sandesh Mahanawar, Vidhin Vijay, Prof. Mukesh Mane "A Design and Development of Special Purpose Machine (SPM) For Drilling and Tapping Operation" International Journal of Scientific Research in Science and Technology(IJSRST), Online ISSN : 2395-602X, Print ISSN : 2395-6011,Volume 3, Issue 4, pp.306-308, May-June-2017.