Model Design of 3-Link Robotic Manipulator Using Maplesim

Authors

  • Obasi C. C.  Department of Computer Engineering, Edo University Iyamho, Edo State, Nigeria
  • Ikharo A. B.  Department of Computer Engineering, Edo University Iyamho, Edo State, Nigeria
  • Okunowo B. A.  Department of Computer Engineering, Federal Polytechnic, Offa, Kwara State, Nigeria
  • Toye N. T.  Department of Computer Engineering, Federal Polytechnic, Offa, Kwara State, Nigeria
  • Oyesetan O. R.  Department of Computer Engineering, Federal Polytechnic, Offa, Kwara State, Nigeria

DOI:

https://doi.org/10.32628/IJSRST207449

Keywords:

Robot, Manipulators, Maplesim, PID, 3-Link, Kinematics, Dynamics

Abstract

Robot design and development is a complex process and require critical analysis to be conducted before the actual implementation. Modern engineering application requires virtual models to be developed and simulated before the actual implementation is carried out. Maplesim has been identified as a tool that can be used for this purpose and has been used in this paper to demonstrate the development of 3-Link robotic manipulator. Design parameters were randomly selected and the symbolic tools in Maplesim were used to model the robot arm. Simulation of the model was done, while adjusting the values of the Proportional Integral Derivative (PID) controllers and the effect on the robot motion was visualized using graphs.

References

  1. K. Raza, T. A. Khan, and N. Abbas, “Kinematic analysis and geometrical improvement ofRaza, K., Khan, T. A., & Abbas, N. (2018). Kinematic analysis and geometrical improvement of an industrial robotic arm. Journal of King Saud University - Engineering Sciences. https://doi.org/10.1016/j.jksu,” J. King Saud Univ. - Eng. Sci., 2018.
  2. R. M. Murray, Z. Li, and S. Shankar Sastry, A mathematical introduction to robotic manipulation. 2017.
  3. F. L. Lewis, D. M. Dawson, and C. T. Abdallah, Robot Manipulator Control. Theory and Practice. 2004.
  4. S. S. Rai, T. A. Gaikwad, and R. V. Kulkarni, “A Research Paper on Simulation Model for Teaching and Learning Process in Higher Education,” Int. J. Adv. Comput. Res., vol. 4, no. 2, pp. 2277–7970, 2014.
  5. P. Badoniya, “Two Link Planar Robot Manipulator Mechanism Analysis with MATLAB,” Int. J. Res. Appl. Sci. Eng. Technol., 2018, doi: 10.22214/ijraset.2018.7132.
  6. S. Kucuk and Z. Bingul, “Robot Kinematics: Forward and Inverse Kinematics,” in Industrial Robotics: Theory, Modelling and Control, 2006.
  7. W. Chen, H. Li, and X. Z. Zhang, “Modelling and analysis of planar robotic arm dynamics based on an improved transfer matrix method for multi-body systems,” 2015, doi: 10.6567/IFToMM.14TH.WC.OS13.046.
  8. MAplesoft, “Robot Manipulators Position, Orientation and Coordinate Transformations,” Online]. Available: https://www.maplesoft.com/engineeringfundamentals/topic.aspx?tid=13.
  9. C. C. Obasi, A. B. Ikharao, V. A. Balogun, A. Odaba, and L. I. Ogbewey, “Computational Analysis of Kinematics of 3 – Links Articulated Robotic Manipulator,” Int. J. Eng. Adv. Technol., vol. 9, no. 2, pp. 3640–3643, 2019.
  10. C. C. Obasi, A. B. Ikharo, A. Odaba, L. I. Ogbewey, and B. A. Oluyomi, “Dynamics of 3 – Links Articulated Robotic Manipulator: A Computational Model,” Int. J. Eng. Adv. Technol., vol. 9, no. 3, pp. 1911–1915, 2020.

International Journal of Scientific Research in Science and Technology

Downloads

Published

2020-09-30

Issue

Volume 7, Issue 5, September-October-2020

Section

Research Articles

License

Copyright (c) IJSRST

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Obasi C. C., Ikharo A. B., Okunowo B. A., Toye N. T., Oyesetan O. R. "Model Design of 3-Link Robotic Manipulator Using Maplesim" International Journal of Scientific Research in Science and Technology(IJSRST), Online ISSN : 2395-602X, Print ISSN : 2395-6011,Volume 7, Issue 5, pp.01-06, September-October-2020. Available at doi : https://doi.org/10.32628/IJSRST207449