Analysis of the Combine ECAP's Heat Treatment for Creating Aluminum Chips, as Well as a Correlation and Regression Analysis of the solid-state data

Authors

  • Suryakant  Department of Physics, Rama Bai Government Women P. G. College, Akabarpur, Ambedkar Nagar, Uttar Pradesh, India
  • Dr. Mahendra Yadav  Department of Physics, Rama Bai Government Women P. G. College, Akabarpur, Ambedkar Nagar, Uttar Pradesh, India
  • Rupesh Kumar Gupta  Department of Physics, Rama Bai Government Women P. G. College, Akabarpur, Ambedkar Nagar, Uttar Pradesh, India
  • Susheel Kumar Singh  Department of Physics, Rama Bai Government Women P. G. College, Akabarpur, Ambedkar Nagar, Uttar Pradesh, India

DOI:

https://doi.org/10.32628/IJSRT52310526

Keywords:

EN AW 6082, correlation and regression analysis

Abstract

The primary objective of this study is to provide a green solution for aluminum recycling. For the aluminum industry to become more circular, it is crucial that innovative recycling methods be developed to maximize the potential for scrap reuse and reduce CO2 emissions. In this article, we discuss how energy and material costs were reduced by recycling aluminum chip waste without first remelting the chips. Solid state recycling or direct recycling are common terms for the method shown here. Chips are cleaned, cold pre-compacted, and hot direct extruded in the solid state recycling process. This is followed by equal channel angular pressing (ECAP) and heat treatment. The effect of artificial aging time and temperature, as well as holding time during solid solution treatment, on the mechanical characteristics of recycled EN AW 6082 aluminum chips was studied. The studies were carried out using a response surface methodology and a design of experiments strategy. The effect of changing the settings of the heat treatment for the proposed solid state recycling process on the mechanical properties of the recycled samples was modeled using a regression analysis. When compared to commercially manufactured EN AW 6082 aluminum alloy in T6 temper condition, the mechanical properties of the recycled samples obtained using the innovative process were found to be comparable. The recycled samples were also analyzed using metallography. Models using regression and correlation analysis have been created to describe the impact of heat treatment settings on the mechanical properties of the generated samples reported in the statistical analysis. using MATLAB as analytical program to conduct correlation and regression.

References

  1. Gopi Krishna M, Praveen Kumar K, Naga Swapna M, Babu Rao J, Bhargava NRMR. Fabrication, characterization and mechanical behaviour of A356/copper particulate reinforced metallic composites. Mater Today Proc 2018; 5:7685-7691.
  2. Dengiz O, Smith AE, Nettleship I. Grain boundary detection in microstructure images using computational intelligence. Comput Ind 2005; 56:854-866.
  3. De Santo M, Liguori C, Paolillo A, Pietrosanto A. Standard uncertainty evaluation in image-based measurements. Meas J Int Meas Confed 2004; 36:347-358.
  4. Dutta S, Das A, Barat K, Roy H. Automatic characterization of fracture surfaces of AISI 304LN stainless steel using image texture analysis. Meas J Int Meas Confed 2012; 45:1140-1150.
  5. Heilbronner R. Automatic grain boundary detection and grain size analysis using polarization micrographs or orientation images. J Struct Geol 2000; 22:969-981.
  6. Cord A, Bach F, Jeulin D. Texture classification by statistical learning from morphological image processing: application to metallic surfaces. J Microsc 2010; 239:159-166.
  7. Coster M, Chermant JL. Image analysis and mathematical morphology for civil engineering materials. Cem Concr Compos 2001; 23:133-151.
  8. Karlı´k M, Kratochvı´l P, Janecek M, Siegl J, Vodi ckov a V. Tensile deformation and fracture micromorphology of an Fe-28Al-4Cr-0.1Ce alloy. Mater Sci Eng, A 2000; 289:182-188
  9. Meakin P. Models for material failure and deformation. Science (80-) 1991;252:226e34. https://doi.org/10.1126/ science.252.5003.226.
  10. Rishabh A, Joshi MR, Balani K. Fractal model for estimating fracture toughness of carbon nanotube reinforced aluminum oxide. J Appl Phys 2010;107
  11. Hilders OA, Ramos M, Pena ND, S  aenz L. Fractal geometry of fracture surfaces of a duplex stainless steel. J Mater Sci 2006; 41:5739-5742.
  12. Frantziskonis G. Heterogeneity and implicated surface effects: statistical, fractal formulation and relevant analytical solution. Acta Mech 1995;108:157-178.
  13. Kozlov HV, Burya OI, Aloev VZ. Application of fractal fracture mechanics to polymers and polymeric composites. Mater Sci 2004; 40:491-496.
  14. Mecholsky JJ, Passoja DE, Feinberg-Ringel KS. Quantitative analysis of brittle fracture surfaces using fractal geometry. J Am Ceram Soc 1989; 72:60-65.
  15. Jiang MQ, Wilde G, Chen JH, Qu CB, Fu SY, Jiang F, et al. Cryogenic-temperature-induced transition from shear to dilatational failure in metallic glasses. Acta Mater 2014; 77:248-257.
  16. Mi Z, Li Q, Hu Y, Liu C, Qiao Y. Fracture properties of concrete in dry environments with different curing temperatures. Appl Sci 2020;10.
  17. Poccia N, Ricci A, Bianconi A. Fractal structure favoring superconductivity at high temperatures in a stack of membranes near a strain quantum critical point. J Supercond Nov Magnetism 2011; 24:1195-1200.
  18. Kotowski P. Fractal dimension of metallic fracture surface. Int J Fract 2006;141:269-286.    [19] Chappard D, Degasne I, Hure G, Legrand E, Audran M, Basle MF. Image analysis measurements of roughness by texture and fractal analysis correlate with contact profilometry. Biomaterials 2003; 24:1399-1407.
  19. Klinkenberg B. A review of methods used to determine the fractal dimension of linear features. Math Geol 1994; 26:23-46.
  20. Sureshkumar P. et al. Effect of strain rate on fractography texture descriptor of AA6063/(Si3N4)x/(Cu(NO3)2)y (x¼12%, y ¼ 2e6%)composite after multiple ECAP passes: second order statistical texture analysis conjunction with regression analysis. Jmr&t 2023;23:2750-2783

International Journal of Scientific Research in Science and Technology

Downloads

Published

2023-10-30

Issue

Volume 10, Issue 5, September-October-2023

Section

Research Articles

License

Copyright (c) IJSRST

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Suryakant, Dr. Mahendra Yadav, Rupesh Kumar Gupta, Susheel Kumar Singh "Analysis of the Combine ECAP's Heat Treatment for Creating Aluminum Chips, as Well as a Correlation and Regression Analysis of the solid-state data" International Journal of Scientific Research in Science and Technology(IJSRST), Online ISSN : 2395-602X, Print ISSN : 2395-6011,Volume 10, Issue 5, pp.136-145, September-October-2023. Available at doi : https://doi.org/10.32628/IJSRT52310526